T3CDS Cable Connector

Electroless Nickel Plated Brass

Click thumbnails for alternate materials

logos

Triton CDS (T3CDS) Ordinary, Wet & Hazardous Location Cable Connector

CMP Triton CDS (T3CDS) Type Cable Connector for use all types of Armored & Jacketed Marine cables incorporating Wire Braid or Served (Single) Wire Armor in Ordinary, Wet & Hazardous Locations, providing a seal on the cable inner bedding and an environmental seal on the cable outer jacket. This product utilises a unique Compensating Displacement Seal (CDS) system which provides full compatibility with Restricted Breathing equipment.

All CMP Cable Glands are EMC Tested.

More +

Less -

The cable connector provides mechanical cable retention and electrical continuity via armor wire termination. A reversible armour cone and AnyWay universal clamping ring arrangement allows the cable to be easily disconnected from the equipment, for maintenance and change out etc. This feature also facilitates remote make off procedures when the termination is to be conducted in confined spaces or in areas of restricted access. Separate tightening actions for the inner Compensating Displacement Seal (CDS) system and the armor termination affords maximum control over the pressure applied to the cable inner bedding.

The T3CDS cable connector is available in NPT (standard) or Metric thread forms and the standard material is Brass grade CuZn39Pb3 (CW614N) to EN12168. This product provides Nema 4X and IP68 ingress protection and is cCSAus listed for use in Class I Zone 1 AEx e II applications and can be used in Class I Division 2 areas when installed in compliance with the NEC requirements.

Cable Gland Selection Table

  • View Metric Table
  • View Imperial Table
Cable Gland Size Available Entry Threads "C" Min Thread Length "E" Cable Lead Sheath Diameter "A" Overall Cable Diameter "B" Armour Range + Across Flats "D" Across Corners "D" Protrusion Length "F" Ordering Reference (NP Brass Metric) # Cable Gland Weight (Kgs)
Standard Option Min Max Min Max Grooved Cone Stepped Cone Max Max
Metric NPT NPT Min Max Min Max
20S/16 M20 1/2" 3/4" 15.0 3.1 8.7 6.1 13.2 0.15 0.5 0.9 1.25 24.0 25.9 70.0 20S16T3CDS1RA531 0.170
20S M20 1/2" 3/4" 15.0 6.1 11.7 9.5 15.9 0.15 0.5 0.9 1.25 24.0 25.9 70.0 20ST3CDS1RA531 0.170
20 M20 1/2" 3/4" 15.0 6.5 14.0 12.5 20.9 0.2 0.5 0.9 1.25 30.5 32.9 72.0 20T3CDS1RA531 0.256
25S M25 3/4" 1" 15.0 11.0 20.0 14.0 22.0 0.2 0.6 1.25 1.6 37.5 40.5 82.0 25ST3CDS1RA532 0.384
25 M25 3/4" 1" 15.0 11.0 20.0 18.2 26.2 0.2 0.6 1.25 1.6 37.5 40.5 82.0 25T3CDSPB1RA532 0.379
32 M32 1" 1 1/4" 15.0 17.0 26.3 23.7 33.9 0.2 0.6 1.6 2.0 46.0 49.7 85.0 32T3CDS1RA533 0.560
40 M40 1 1/4" 1 1/2" 15.0 22.0 32.2 27.9 40.4 0.2 0.8 1.6 2.0 55.0 59.4 86.0 40T3CDS1RA534 0.848
50S M50 1 1/2" 2" 15.0 29.5 38.2 35.2 46.7 0.2 0.8 2.0 2.5 60.0 64.8 98.0 50ST3CDS1RA535 1.055
50 M50 2" 2 1/2" 15.0 35.6 44.1 40.4 53.1 0.3 0.8 2.0 2.5 70.0 75.6 100.0 50T3CDSPB1RA536 1.521
63S M63 2" 2 1/2" 15.0 40.1 50.0 45.6 59.4 0.3 0.8 2.0 2.5 75.0 81.0 108.0 63ST3CDS1RA536 1.750
63 M63 2 1/2" 3" 15.0 47.2 56.0 54.6 65.9 0.3 0.8 2.0 2.5 80.0 86.4 103.0 63T3CDS1RA537 1.685
75S M75 2 1/2" 3" 15.0 52.8 62.0 59.0 72.1 0.3 0.8 2.5 3.0 89.0 96.1 105.0 75ST3CDS1R5737 2.345
75 M75 3" 3 1/2" 15.0 59.1 68.0 66.7 78.5 0.3 0.8 2.5 3.0 99.0 106.9 114.0 75T3CDS1RA538 3.200
90 M90 3" 3 1/2" 15.0 66.6 80.0 76.2 90.4 0.4 0.8 3.15 4.0 114.0 123.1 140.0 90T3CDS1RA539 5.100
Dimensions are displayed in millimetres unless otherwise stated

NOTE: +Alternative armour clamping range available for non-standard armour sizes. # Other thread forms are available.

Cable Gland Size Available Entry Threads "C" Min Thread Length "E" Cable Lead Sheath Diameter "A" Overall Cable Diameter "B" Armour Range + Across Flats "D" Across Corners "D" Protrusion Length "F" Ordering Reference (NP Brass Metric) # Cable Gland Weight (Ozs)
Standard Option Min Max Min Max Grooved Cone Stepped Cone Max Max
Metric NPT NPT Min Max Min Max
20S/16 M20 1/2" 3/4" 0.591 0.122 0.343 0.240 0.519 0.000 0.039 0.035 0.049 0.945 1.020 2.756 20S16T3CDS1RA531 6.00
20S M20 1/2" 3/4" 0.591 0.240 0.461 0.374 0.626 0.000 0.039 0.035 0.049 0.945 1.020 2.756 20ST3CDS1RA531 6.00
20 M20 1/2" 3/4" 0.591 0.256 0.551 0.492 0.823 0.000 0.039 0.035 0.049 1.201 1.295 2.835 20T3CDS1RA531 9.03
25S M25 3/4" 1" 0.591 0.433 0.787 0.551 0.866 0.000 0.039 0.049 0.063 1.476 1.594 3.228 25ST3CDS1RA532 13.55
25 M25 3/4" 1" 0.591 0.433 0.787 0.717 1.031 0.000 0.039 0.049 0.063 1.476 1.594 3.228 25T3CDSPB1RA532 13.37
32 M32 1" 1 1/4" 0.591 0.669 1.035 0.933 1.335 0.000 0.039 0.063 0.078 1.811 1.957 3.346 32T3CDS1RA533 19.75
40 M40 1 1/4" 1 1/2" 0.591 0.866 1.268 1.098 1.591 0.000 0.039 0.063 0.078 2.165 2.339 3.386 40T3CDS1RA534 29.91
50S M50 1 1/2" 2" 0.591 1.161 1.504 1.386 1.839 0.000 0.039 0.078 0.098 2.362 2.551 3.858 50ST3CDS1RA535 37.21
50 M50 2" 2 1/2" 0.591 1.402 1.736 1.591 2.091 0.000 0.039 0.079 0.098 2.756 2.976 3.937 50T3CDSPB1RA536 53.65
63S M63 2" 2 1/2" 0.591 1.578 1.969 1.795 2.339 0.000 0.039 0.079 0.098 2.953 3.189 4.252 63ST3CDS1RA536 61.73
63 M63 2 1/2" 3" 0.591 1.858 2.205 2.150 2.594 0.000 0.039 0.079 0.098 3.150 3.402 4.055 63T3CDS1RA537 59.44
75S M75 2 1/2" 3" 0.591 2.078 2.441 2.323 2.839 0.000 0.039 0.098 0.118 3.504 3.783 4.134 75ST3CDS1RA537 82.72
75 M75 3" 3 1/2" 0.591 2.326 2.677 2.626 3.091 0.000 0.063 0.098 0.118 3.898 4.209 4.488 75T3CDS1RA538 112.88
90 M90 3" 3 1/2" 0.591 2.622 3.148 3.000 3.559 0.000 0.063 0.124 0.157 4.488 4.846 5.512 90T3CDS1RA539 179.90
Dimensions are displayed in inches unless otherwise stated

NOTE: +Alternative armour clamping range available for non-standard armour sizes. # Other thread forms are available.

TECHNICAL DATA
Lloyds Approval No. 01/00172
DNV Approval No. E-10496
ABS Approval No. 01-LD234401A/2-PDA
INMETRO Approval Number MC-AEX-7041-X
INMETRO Code of Protection Category BR-Ex d IIC / BR-Ex e II
INMETRO Compliance Standards ABNT NBR IEC 60079-0:2006, ABNT NBR IEC 60079-1:2007, ABNT NBR IEC 60079-7:2001 e ABNT NBR IEC 60528:2005
GOST R Certificate Number POCC GB.HO06.B00207
GOST R Code of Protection Category Ex d IIC / Ex e II / DIP A21
GOST R Compliance Standards ГOCT P 52350.0-2005, ГOCT P 52350.1-2005,
ГOCT P 52350.7-2005, ГOCT MЭK 61241-1-1-99
GOST GGTN Permit PPC 00-40706
GOST K Certificate Number KZ 75000361 01 01 14761
RoK Permit For Use Number 19-02-UL-1957
NEPSI Certificate Number GYJ081070
NEPSI Code of Protection Category Ex d IIC, Ex e II, Ex nR II, DIP A21 TA
NEPSI Compliance Standards GB3836.1/2/3, GB3836.8-2003, GB12476.1-2000
RETIE Approval Number 03866
Type T3CDS
Design Specification BS 6121:Part 1:1989, EN 50262:1999, UL 514B, IEC 62444:2010
ATEX Certification Detail SIRA06ATEX1283X, SIRA07ATEX4328X
ATEX Code of Protection Category ATEX ATEX Approved II 2 GD, Ex d IIC, Ex e II, Ex tD A21 IP66, ATEX ATEX Approved II 3 G Ex nR II
ATEX Compliance Standards EN 60079-0, EN 60079-1, EN 60079-7, EN 60079-15, IEC 61241-0, IEC 61241-1
IEC Ex Certification Detail IECEx SIR 07.0005X
IEC Ex Code of Protection Category Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66
IEC Ex Compliance Standards IEC 60079-0, IEC 60079-1, IEC 60079-7, IEC 60079-15, IEC 61241-0, IEC 61241-1
cCSAus Approval Certificate No. 1310517
cCSAus Code of Protection Category

Class I, Div 2, Groups ABCD; Class II, Div 2, Groups EFG; Class III; Ex d IIC; Ex e II; Class I, Zone 1, AEx d IIC; Class I, Zone 1, AEx e II

cCSAus Compliance Standards CAN/CSA-C22.2 No 0-M91, CAN/CSA-C22.2 No 18-04, CAN/CSA-C22.2 No 25-1966, CAN/CSA-C22.2 No 30-M1986, CAN/CSA-C22.2 No 174-M1984, CAN/CSA-C22.2 No 94-M91, CAN/CSA-E60079-0:07, CAN/CSA-E60079-7:07, CAN/CSA-E60079-1:07, ANSI/UL 514B Edition 5, ANSI/UL 50 Edition 11, ANSI/UL 2225 Edition 4, UL60079-0:07, UL60079-7:07, UL60079-1:07
Continuous Operating Temperature -60°C to +130°C
Ingress Protection Rating IP66, IP67, IP68
Deluge Protection Compliance DTS01 : 91
Deluge Protection Document ITS 01005029 - D
EMC Test Information EMC_Test_Report_DUR23743
Cable Gland Material Brass, Electroless Nickel Plated Brass, Aluminium, Stainless Steel
Seal Material CMP SOLO LSF Thermoplastic Elastomer
Cable Type Aluminium Strip Armour (ASA), Screened Flexible Wire Braid (e.g. CY / SY), Single Wire Armour (SWA), Aluminium Wire Armour (AWA), Pliable Wire Armour (PWA), Steel Tape Armour (STA), Wire Braid Armour (e.g. SWB), Armored & Jacketed
Armour Clamping Reversible Armour Cone & AnyWay Universal Clamping Ring
Sealing Technique CMP Inner Compensating Displacement Seal System (CDS) & Outer Load Retention Seal (LRS)
Sealing Area(s) Cable Inner Bedding & Outer Cable Sheath
Accessories Adaptor/Reducer, Earth Tag, Locknut, Serrated Washer, Entry Thread Seal, Shroud

Note: Versions with dedicate braid armour cones also available.

The Stepped side of the cone is suitable for SWA cables, and the Grooved side of the cone is suitable for all other approved armoured cables.

Additional information

Close [-]

If you cannot view this video please email us for details - webmaster@cmp-products.com

Close [-]

If you cannot view this video please email us for details - webmaster@cmp-products.com

CMP WP T3CDS/USA_0311